PSE4P-CSP165 - 8,000 LB. 4 Post Portable Car Stacker Lift
Product Inquiry Form
Please fill out the form below to inquire about this product.
APPLY NOW: We Offer Financing Plans as Low as $49/Month
Couldn't load pickup availability
Speak to a Team Member Now About this Product
Call Us: 317-736-5094
Emergency Service: 317-833-0989
Toll Free number: 888-736-5094
Email us: Sales@dwipower.com
.
All Equipment sold through Pro-Series Equipment is Distributed by DWI Power Systems!
The PSE4P-CSP165 is a standard 8,000LBS 4 Post Lift designed with car collectors, hobby mechanics and those looking to add parking space to their garage in mind. The PSE4P-CSP165 is over 1' Smaller, 1' Shorter than the standard 4 Post 180” parking Lifts!
INCLUDES:
- FREE Complete 4 Piece Caster Kit This Makes The PSE4P-CSP165 is Portable! It can also be anchored down for permanent use.
- FREE 3 Plastic Drip Trays
- FREE 1 Steel Jack Tray
- FREE Two Detachable 34" Steel Approach Ramps
- FREE 4 Detachable Runway Stop Plates
- ATTENTION: Many of the included items listed above are sold as separate accessories by our competitors - with the PSE4P-CSP165, you get the COMPLETE Package!
- Also Includes Many Other Features!
Customers can leave our CSP Branded Lifts unanchored to the floor to allow portability, or can anchor the lift to the floor to provide extra stability and lift strength for heavier loads.
We also carry a full line of Bridge Jacks for use on our CSP Model Lifts, which can also be used with almost any 4 Post Hobbyist Lift on the market today!
PRODUCT DETAILS:
Product Features:
- The PSE4P-CSP165 is made for Smaller vehicles such as Hot Rods, Muscle cars and is designed for small Garages! The PSE4P-CSP165 6,000LBS Lift Can be custom built to fit through small garage doors. Call for details!
- 110V Power Unit: The 110V Power Unit simplifies setup and makes this lift very easy to setup!
- Single Point Lock Release: The Lock Release design on our 4-Post lifts makes disengaging the safety locks a fast, simple, ONE Step process!
- Car Stop Plates: 4 Car Stop Plates are included to allow you to secure vehicles from the front and rear, preventing accidents and increasing safety!
- Steel Jack Tray: A sliding, Heavy Duty Jack Tray is included to provide a platform for lifting vehicles off of the Runways as needed for maintenance.
- 3 Drip Trays: The 3 Included Drip Trays with the PSE4P-CSP165 help collect waste oil and also help protect vehicle parked underneath!
- Heavy Duty Steel Aircraft Cables: Our Portable 4-Post Lifts utilize a Heavy-Duty Braided Steel Aircraft Cable driven design and use only one Hydraulic Cylinder.
- Steel Block Safety Latch Locking System: The Locking System on the PSE4P-CSP180 uses Heavy Duty Steel Components for maximum safety!
- 34" Approach Ramps: With 34" Drive-On Approach Ramps and Diamond Plate design, getting vehicles onto this lift is easy! This provides a low angle approach and means that Low Profile vehicles are NO Problem!
- Complete Polyurethane Coated Caster Kit: The Included Polyurethane Coated Caster Kits provide smooth rolling action when moving this lift.
MODEL NUMBER: | PSE4P-CSP165 |
---|---|
Capacity: | 8,000 LBS. |
Configuration: | Portable |
Configuration: | Anchored |
Gauge of Steel: | .240" |
Post Dimensions: | 4" x 6" |
Shipping Weight: | 2,100 LBS. |
PHYSICAL DIMENSIONS: | |
Overall Height: | 86" |
Runway Length (w/ Ramps) | 204.5" |
Runway Length (w/OUT Ramps) | 165¾" |
Width Outside Posts: | 106.5" |
Clearance Between Posts: | 93" |
Width of Runways: | 18½" |
Max. Outside Width of Both Runways Custom: | 76.5" |
Front To Rear Clearance Between Post | NA |
VEHICLE LIFTING SPECS: | |
Max. Lifting Height to Top of Runways: | 73.5½" |
Max. Lifting Height on Top Lock: | 72.5½" |
Max. Clearance Under Runways: | 69½" |
Max. Clearance on Top Lock: | 79¼" |
Lifting Speed (Approx.) | 71 Seconds |
POWER UNIT SPECS: | |
Motor HP: | 2HP |
Motor Voltage: | 110V |
Phase / Frequency / AMP | 1 P / 60 Hz / 20 AMP |
SHIPPING INFORMATION:
Packaging Information:
This equipment weighs approximately 2,100 LBS. If you have any questions or would like more information on this equipment, Call 1-888-736-5094 to speak to a Pro-Series Equipment rep today.
Shipping Process:
This equipment will ship as a FREIGHT item via LTL common carrier. The customer is responsible for providing a shipping address that will be able to accept the shipment. Customers are responsible to ensure that the shipping address provided will be able to accommodate a large 18 wheel truck pulling into the drive / dock without any problems.
It is also the responsibility of the customer to unload the equipment from the truck when it is delivered. Due to the size and weight of the equipment, a forklift or wrecker boom will be required!
If the customer is unsure if the truck will be able to unload the shipment on their drive, and they do not have access to a commercial dock, it is strongly recommended that the equipment be delivered to a trucking terminal in the customer's area. The terminal staff will be able to unload the equipment from the trailer and load it onto a truck or trailer at no additional cost.
Shipping Method: | Freight (LTL) |
---|---|
Shipping Length: | 167" |
Shipping Height: | 26½" |
Shipping Width: | 21½" |
Shipping Weight | 2,100 LBS. |
For more information on shipping policies for Pro-Series Equipment, click here.
INSTALLATION OVERVIEW:
This lift will come packaged between two steel shipping plates. The Power Unit will be banded to the lift, and all of the components, hardware and anchor bolts will be packaged inside the lift columns.
Required Tools & Materials:
You will need the following items in order to install this lift:
Concrete Rotary Hammer Drill w/ ¾" Carbide Bit, Rubber Hammer, 2 LB. Sledge Hammer, Chalk Line & Square, Socket Wrenches, Open End Wrenches, Ratchet Driver, Locking Pliers, Measuring Tape, Screwdrivers, Torque Wrench, Step Ladder, 4' Bubble Level, & 12" Adjustable Wrench.
You will also need to have 3 Gallons of AW-32 non-foaming, non-detergent Hydraulic Fluid.
Electrical Requirements:
This lift requires a 120V, Single Phase power supply on a dedicated 20 AMP circuit breaker. All electrical wiring for this lift should be done by a certified electrician!
Concrete Requirements:
The lift should be installed on a level floor with a minimum of 4" - 6" of 3,000 psi concrete (sufficiently cured). If you are unsure of the thickness of the concrete, it is best to test drill where the lift is to be installed to verify the depth of the concrete.
Installation Overview:
The instructions in the included manual should be carefully followed step by step. Our lifts are often installed by our customers, and usually will take from 4-5 hours to finish. Professional lift installation services are likely available in your area for a fee, please consult your sale representative if you are interested in learning more!